Get NACE-CIP1-001 Braindumps & NACE-CIP1-001 Real Exam Questions

NACE NACE-CIP1-001 Actual Questions and Braindumps

NEW QUESTION # 40
Digital hygrometers

• A. consist of a bimetallic sensing element protected from wind gusts.
• B. determine relative humidity, air temperature, and dew point temperature:
• C. are used to measure temperature from a distance.
• D. use a thermocouple in contact with the surface to measure temperature

Answer: B

NEW QUESTION # 41
Stripe coats are best applied by:

• A. High volume low pressure spray
• B. Airless spray
• C. Brush
• D. Conventional spray

Answer: C

NEW QUESTION # 42
It is good practice for the NACE Inspector to have instrument calibration certificates available:

• A. At all times
• B. Only if the specification requires it
• C. In the office only
• D. In the field only

Answer: A

NEW QUESTION # 43
NACE SP 0178 is a standard for:

• A. Stainless steel pipe to be Externally Coated
• B. Tanks and Vessels to, be Lined for Immersion Service
• C. Tanks and Vessels to be Externally Coated
• D. Structural steel to be coated for Atmospheric Service

Answer: B

NEW QUESTION # 44
Which is a component that supplies most of the features and functions of the material?

• A. additive
• B. binder
• C. solvent
• D. pigment

Answer: B

NEW QUESTION # 45
Whenever dissimilar metals must join, the most common practice is to

• A. coat all connected dissimilar metals.
• B. provide anodic protection to prevent corrosion.
• C. provide cathodic protection to prevent corrosion,
• D. avoid coating all connected dissimilar metals.

Answer: A

NEW QUESTION # 46
A single application coating film has a measured dry film thickness (DFT) between 4 and 5 mils (between 100 and 125 microns). The volume solids of the coating immediately before application were 67%, What wet film thickness (WFT) was applied?

• A. 8 to 10 mils (200 to 250 microns)
• B. 10 to 12 mils (250 to 300 microns)
• C. 5 to 6 mils (125 to 150 microns)
• D. 6 to 7 mils (150 to 175 microns)

Answer: D

NEW QUESTION # 47
Most industrial coatings are:

• A. Resistant to temperatures above 200C
• B. Organic
• C. Inorganic
• D. Resistant to concentrated sulfuric acid

Answer: B

NEW QUESTION # 48
When working as a NACE Inspector in a situation where there is a difference of opinion, the Inspector needs to:

• A. Go with the majority opinion
• B. Never change his/her mind
• C. Achieve consensus through negotiation
• D. Call the supervisor

Answer: D

NEW QUESTION # 49
Owners hire NACE Inspectors' with the expectation that:

• A. The inspection cost will be offset by an improvement in service life
• B. The Inspector will make a meaningful technical contribution to the job
• C. a) and c)
• D. The Inspector will improve job flow and schedule

Answer: C

NEW QUESTION # 50
Upon arrival of coating materials, the inspector should

• A. observe and document the amount of material and batch numbers.
• B. observe and document time frame and environmental conditions between each coat.
• C. observe aryl document that the applicator WFT at regular intervals during application.
• D. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.

Answer: A

NEW QUESTION # 51
You are asked to be the only coating inspector on a small bridge recoating job where existing coating contains lead. The owners' representative has supplied you with the local code governing the removal and disposal of lead based coatings, however upon reading the document you having great deal of difficulty understanding the technical language.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

• A. Carefully review the document and do the best you can
• B. Minimize your lack of understanding and go ahead with the inspection task to the best of your ability
• C. Advise the owners' representative of your lack of knowledge in this area
• D. Hire a third patty to assist you in understanding the document

Answer: A

NEW QUESTION # 52
Safety Data Sheets must be carefully reviewed by:

• A. The Application personnel
• B. The Owner's personnel
• C. All personnel involved in the job
• D. The Inspection personnel

Answer: C

NEW QUESTION # 53
The primary difference between Non-Convertible vs. Convertible coatings is:

• A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
• B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
• C. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
• D. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not

Answer: C

NEW QUESTION # 54
Conventional spray is a good choice when:

• A. High quality finishes are required
• B. High viscosity coatings are being applied
• C. High transfer efficiency is required
• D. High production rates are required

Answer: A

NEW QUESTION # 55
ISO SA 3 is directly equivalent to:

• A. NACE No. 1/SSPC SP 5
• B. None of the above
• C. NACE No. 3/SSPC SP 6
• D. NACE No. 2/SSPC SP 10

Answer: B

NEW QUESTION # 56
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:

• A. Call the coating manufacturer for clarification
• B. Use the product data sheet as a guide
• C. Call the person who wrote the specification for clarification
• D. Use the job specification as a guide

Answer: D

NEW QUESTION # 57
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a

• A. blotter test for the presence of oil and water.
• B. vial lest.
• C. wet film thickness (WFT) measurement.
• D. dry film thickness (DEI) measurement.

Answer: A

NEW QUESTION # 58
Silicone coatings are typically:

• A. Applied in very' thin films
• B. Applied in very thick films
• C. Used strictly in immersion service
• D. Used as a sacrificial primer

Answer: A

NEW QUESTION # 59
When using a sling physchrometer a very large difference between the wet and dry bulb readings indicates:

• A. High Relative Humidity
• B. Low Surface Temperature
• C. High Surface Temperature
• D. Low Relative Humidity

Answer: D

NEW QUESTION # 60
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:

• A. Surface Condition H
• B. Rust Grades 1-4
• C. Rust Grades A-D
• D. Surface Conditions E-G

Answer: C

NEW QUESTION # 61
......

NACE-CIP1-001 Dumps To Pass NACE Exam in 24 Hours - BraindumpsIT: https://www.braindumpsit.com/NACE-CIP1-001_real-exam.html

Buy Latest NACE-CIP1-001 Exam Q&A PDF - One Year Free Update: https://drive.google.com/open?id=1f4UTXyzqRdknuMvcgUcyffDderE9CVhn